pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 document no. doc000924 d pnspo ! P1TX6A-SX51-01M product specification sheet sheet 1 of 10 confidential information P1TX6A-SX51-01M product specification sheet
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 1.0 description the p1tx6-sx51-01m (tx-sx51) is an optical module that transmits an hdmi? signal on one strand of multimode fiber. the tx-sx51 incorporates a bi- directional optical subassemb ly (osa) to convert and transmit an uncompressed electrical hdmi? video signal, along with the hdc p/edid/cec functionality, over distances of up to 1000m. 2.0 features ? 5 transmit lanes and 1 receive lane over 1 multimode fiber ? compatible with hdmi? compliant sources and sinks ? scalable to hdmi? 1.3a 16-bit color ? on-board hardware and firmware for hdcp/edid/cec functionality ? accepts tmds inputs directly into its 40 pin plug-down connector ? automatic laser disable upon fiber disconnect this device is extremely sensitive to electrostatic discharge (esd). at a minimum, all handling must be performed in accordance with an ansi-compliant esd control program (ansi/esd s20.20-2007) to mitigate possible esd-induced damage. reliability and life of the de vice will be adversely affected if these precautions are not met. this device is a class 3r laser device (per iec 60825-1:2007) and can cause damage to eye sight if used improperly. refer to ansi z136 for proper handling and usage of class 3r devices. hdmi, the hdmi logo and high-definition mu ltimedia interface are trademarks or regi stered trademarks of hdmi licensing llc. document no. doc000924 d P1TX6A-SX51-01M product specification sheet sheet 2 of 10 pnspo ! confidential information
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 document no. doc000924 d pnspo ! P1TX6A-SX51-01M product specification sheet sheet 3 of 10 confidential information 3.0 absolute maximum ratings parameter symbol min typ max units storage temperature 1 , 3 tst -40 85 c 3.3v supply voltage vcc1 -0.3 3.6 v 5.0v supply voltage vcc2 -0.5 6 v operating surface temperature 2 ta 0 65 c operating humidity 3 rh 80 % durability ? sc connector 200 cycles durability ? plug-down connector 50 cycles 4.0 optical characteristics ? high-speed lanes parameter (per lane) symbol min typ max units average optical power, per lane 4 pout -3.0 0.0 dbm optical modulation amplitude -6.25 dbm center wavelength ? lane 0 778 nm center wavelength ? lane 1 800 nm center wavelength ? lane 2 825 nm center wavelength ? lane 3 850 nm 1 stresses listed may be applied without causing damage. functionality at or above the values listed is not implied. exposure t o these values for extended periods may affect reliability. 2 see outline drawing for measurement point. 3 non condensing, 80% rh. 4 i= 5ma, t=25c.
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 document no. doc000924 d pnspo ! P1TX6A-SX51-01M product specification sheet sheet 4 of 10 confidential information 5.0 electrical specifications ? high-speed lanes parameter symbol min typ max units data rate per lane 5 p1tx6-sx51v-01m p1tx6-sx51d-01m 1.65 3.50 gb/s total jitter (rms), per lane 6 t j1 10 ps input differential impedance 100 ohm differential input voltage 7 320 2000 mvp-p single-ended input voltage 160 1000 mvp-p common mode input voltage (ac-coupled input) 0.85 2.6 vcc v v operating 3.3v supply volt age vcc1 3.15 3.30 3.45 v operating 3.3v supply cu rrent icc1 235 ma operating 5.0v supply vo ltage vcc2 4.75 5 5.25 v operating 5.0v supply cu rrent icc2 35 ma 6.0 optical characteristics ? low-speed lanes laser parameter symbol min typ max units wavelength - lane 4 911 nm data rate 5 mb/s average optical power pavg -0.5 dbm photodiode parameter symbol min typ max units wavelength - lane 5 980 nm data rate 5 mb/s maximum optical input power pin 8 dbm 5 measured with input signals conforming to hd mi? rev 1.3a, section 4.2.4, figure 4-18. 6 based on a jitter-free source 7 differential cml compatible inputs
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 document no. doc000924 d pnspo ! P1TX6A-SX51-01M product specification sheet sheet 5 of 10 confidential information 7.0 hdmi? signal parameters hdmi? signal parameter 8 symbol min typ max units hdmi? input signal ? scl ih ,sda ih v ih 3.5 5.75 v hdmi? input signal ? scl il ,sda il v il -0.5 1.5 v hot plug detect high hpd h 2.4 5.3 v hot plug detect low hpd l 0 0.4 v cec 9 output voltage logic ?0? v cec0 0 0.6 v cec output voltage logic ?1? v cec1 2.5 3.63 v high to low input voltage threshold logic ?0? v cect0 0.0 0.8 v low to high input voltage threshold logic ?1? v cect1 2.0 3.63 v cec rise time (10% to 90%) t cecrise 250 s cec fall time t cecfall 50 s 8.0 status signal functional table 10 condition status signal pin output source cable source status sink cable sink status optical cable ss 1 ss 2 ss 3 ss 4 x x x x d t 0 0 0 c on c on c 0 0 0 0 c off c on c 0 0 0 1 c x d x c 0 0 1 1 c x c off c 0 0 1 1 d x x x c 0 1 1 1 x does not affect output d disconnected c connected t toggles between 0 and 1 at ~ 10hz 0 0 volts 1 5 volts 8 reference i 2 c-bus specification v2 and hdmi? rev 1.3a. supports up to 100khz bus speed. 9 the firmware version installed in the module must be version 2.10.06 or higher for cec functionality. update to version 2.10.0 6 or higher if the current version is not at this revision level. refer to p1_x6-sx51-01m bootlo ader manual for updating details. 10 status signal table represents typical output. variances in st atus signals may occur between different manufacturers and/or mo dels of sources and sinks.
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 document no. doc000924 d pnspo ! P1TX6A-SX51-01M product specification sheet sheet 6 of 10 confidential information 9.0 fiber transmission distance data rate skew limit om1 (160 mhz*km) om2 (500 mhz*km) om3 (1000 mhz*km) units none 200 400 1000 m 1.65 gbps 2.42ns 200 400 400 m none 100 200 500 m 3.50 gbps 2.42ns 100 200 400 m 10.0 laser safety the p1tx6-sx51-01 meets class-3r requireme nts. use proper eye protection and handling practices per ansi z136. 11.0 firmware 11 the firmware utilized with the p1tx6- sx51-01m has been evaluated through the following functional tests: 11.1 hdcp compliance test (source) 1a-01 through 1a-09, 1b-01 through 1b-06 11.2 hdcp compliance test (sink) 2c-01 through 2c-04 11.3 hdcp compliance test (repeater) 3c-i-01 through 3c-i-07, 3c-ii-01 through 3c-ii-09, 3a-01 through 3a-05, 3b-01 through 3b-05 11.4 edid for hdmi? compliance test (display sink devices) 8-1, 8-2, 8-3, 8-17, 8-18, 8-19 11.5 cec compliance tests 7-1, 7-2, 8.1, 8.2, 9.1 through 9.5, 9.7-1, 10.1.1.1-1, 10.1 .2, 10.2.3, 11.1 .2-2, 11.1.3-2, 11.1.6-1 through 11.1.6-4, 11.2.1-1, 11.2.2-2, 11.2.2-3, 11.2.3-2, 11.2.6-1, 11.2.6-2, 11.2.7-3 through 11.2.7-6, 11.2.7-12, 11.2.7-13, 11.2.14-1, 12-1 through 12-3 12.0 connectivity the p1tx6-sx51-01m will support up to eight key selection vectors (ksv) allowing for up to eight hdcp compliant devices to be connected downstream from the sx51-01m link. 11 firmware is not warranted for interoperability with all hdmi tm sources and sinks.
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 document no. doc000924 d pnspo ! P1TX6A-SX51-01M product specification sheet sheet 7 of 10 confidential information 13.0 patents this product contains the following patents or patents pending: 6201908, 6396978, 6456757, 6558046, 6572278, 6652161.
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 document no. doc000924 d pnspo ! P1TX6A-SX51-01M product specification sheet sheet 8 of 10 confidential information 14.0 tosa module pin numbers and descriptions the sx51 tx module utilizes a 40 pin plug-down connector. recommended mounting position is on the top of the boa rd and secured in place with mounting screws located along the bottom face of th e module enclosure. for information on the specifications of the connector, contact hirose (df12 (5.0)-40dp-0.5v). pin # name description 1 tmds 2 + positive differential tmds 2 signal (850nm) 2 vcc1 +3.3v power supply 3 gnd ground 4 vcc1 +3.3v power supply 5 tmds 2 - negative differential tmds 2 signal (850nm) 6 reserved reserved for omron future use ? do not connect 7 tmds 1 + positive differential tmds 1 signal (825nm) 8 reserved reserved for omron future use ? do not connect 9 gnd ground 10 reserved reserved for omron future use ? do not connect 11 tmds 1 - negative differential tmds 1 signal (825nm) 12 reserved reserved for omron future use ? do not connect 13 tmds 0 + positive differential tmds 0 signal (800nm) 14 ss 1 fiber connect status signal 15 gnd ground 16 ss 2 5v source status signal 17 tmds 0 - negative differential tmds 0 signal (800nm) 18 ss 3 hot plug sink status signal 19 clk + positive differential clk signal (778nm) 20 ss 4 video detect status signal
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 document no. doc000924 d pnspo ! P1TX6A-SX51-01M product specification sheet sheet 9 of 10 confidential information tosa module pin numbers and descriptions (cont?d) pin # name description 21 gnd ground 22 nc 12 do not connect 23 clk - negative differential clk signal (778nm) 24 nc do not connect 25 src_cec source cec 13 26 nc do not connect 27 nc do not connect 28 reserved reserved for omron future use 29 src_scl source clock 14 30 nc do not connect 31 src_sda source data 32 nc do not connect 33 gnd ground 34 reset module reset 14 (must be asserted to +5v for normal operation) 35 src_5v source 5v signal 15 36 vcc2 +5v power supply 37 src_hpd source hot plug detect signal 38 vcc2 +5v power supply 39 gnd ground 40 gnd ground 12 nc = do not connect this pin 13 internal 27.4k ? pull-up to 3.3v 14 internal 47k ? pull-up to 5v 14 see information package for mechanical reset circuit 15 internal 10k ? pull-down to ground
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 15.0 dimensions the sx51 tx module is designed to work with a standard sc ferrule only. insertion of any other type may result in damage. for dust cap information, contact l-com (dstcp-sc). dimensions and orientation are for reference only. document no. doc000924 d P1TX6A-SX51-01M product specification sheet sheet 10 of 10 pnspo ! confidential information all dimensions are in mm. **temperature measurement point
|
